ユーザーマニュアル

• ADJUSTING MESH AND LINK BRACELETS
  

  ADJUSTABLE MESH BRACELET

  1. Open the security clasp and buckle. Put your watch on a flat surface.
  2. Insert a tool * into the opening and pry open. Do not force too much.

     * Small screw driver or similar

  3. Adjust the slider to the desired position, lining up with the indentations on the back.
  4. Use the tool * again to close, flipping the tool the opposite way.
  5. Put your watch on. Close the buckle and the security clasp.
• STANDARD INSTRUCTIONS – SET DATE AND TIME
  

  SET THE DATE AND TIME

  1. Pull the crown out to the 2nd position.
  2. Turn the crown counter-clockwise to set the date*.
  3. Pull the crown out to the 3rd position. Turn the crown to set hour and minute hands.
  4. When the crown is pushed back to the 1st position, the second hand begins to run.

  *If the date is set between the hours of 9 p.m. and 1 a.m., the date may not change the following day.
• MULTIFUNCTION DAY / DATE
  

  1. SET THE DAY
     Pull the crown to the 3rd position. Turn the hands in a clockwise direction to set the day. The hands should be turned clockwise, advancing the hour hand by 24 hours per day.
     NOTE: Do not set the day by turning the crown in a counterclockwise direction, as there is a possibility that the date will not change over if set in this way.
     *The day changes somewhere between 0:00 a.m. and 5:30 a.m. or a little later.
  2. SET THE TIME
     To ensure the time is set accurately, first turn the minute hand 5 minutes ahead of desired time and then turn back (counterclockwise) to the desired time. When the crown is pushed back to the 1st position, the second hand begins to run.
     NOTE: Make sure you have correctly set the a.m. / p.m. before setting the time. When the day changes over, it is a.m.
  3. SET THE DATE (BY QUICK OPERATION)
     Pull the crown to the 2nd position. Turn the crown counterclockwise.
     Note: Do not set the date between the hours of 9 p.m. to 00.30 a.m. as the date may not change correctly the next day.
• MULTIFUNCTION DATE / 24 HOUR
  

  1. SET THE TIME
     Pull the crown to the 3rd position. Turn the hands in a clockwise direction to set the time. To ensure the time is set accurately, first turn the minute hand 5 minutes ahead of desired time and then turn back (counterclockwise) to the desired time.
     NOTE: Make sure you have correctly set a.m. / p.m. before setting the time. When the day changes over, it is a.m. (day changes over between 0:00 a.m. and 5:30 a.m. or a little later). Check a.m. / p.m. by the 24 hour hand.
  2. SET THE DATE (BY QUICK OPERATION)
     Pull the crown to the 2nd position. Turn the crown counterclockwise.
     Note: Do not set the date between the hours of 9 p.m. to 00.30 a.m. as the date may not change correctly the next day.
• MULTIFUNCTION DAY / DATE / 24 HOUR
  

  1. SET THE TIME/DAY
     Please make sure you have correctly set am/pm before you start to adjust the time.
     Pull the crown out to the 2nd position when the second hand points to 0(12 o’clock).
     After setting the time, use a time signal to synchronize the watch by pushing the crown to the normal position to start the second hand going.
     You can not quickly adjust the day of the week.
     In order to adjust the day, you must advance the hour hand by 24 hours per day.
     Always rotate the hour and minute hand in a clockwise direction to set the day. If you rotate the hands in a counter-clockwise direction, it may not always change the day correctly.
  2. SET THE DATE
     Pull the crown out to the first position
     Turn the crown to the left to set the date.
     You can not adjust the date between approximately 9pm and 0:30am.
     After setting the time/date/day of the week, please push the crown back to it’s normal position before using.
• CHRONOGRAPH
  

  SET THE DATE AND TIME

  1. Pull the crown out to the 2nd position.
  2. Turn the crown counter-clockwise to set the date*.
  3. Pull the crown out to the 3rd position. Turn the crown to set the hour and minute hands.
  4. When the crown is pushed back to the 1st position, the second hand begins to run.
     *If the date is set between the hours of 9 p.m. and 1 a.m., the date may not change the following day.

  USING THE CHRONOGRAPH
  This chronograph is able to measure and display time in 1/1 second united up to a maximum of 59 minutes and 59 seconds.

  • Press button A to start or stop the watch.
  • Press button B to reset the stopwatch in its original position.

  RESETTING THE CHRONOGRAPH (ALSO AFTER REPLACING BATTERY)
  When the chronograph second hand does not return to zero position after it has been reset and when the battery has been replaced.

  1. Pull the crown out to the 3rd position.
  2. Press button A to set the chronograph second hand to the zero position.
     The chronograph hand can be advanced rapidly by continuously pressing button A.
  3. Return the crown to position 1.
• SOLAR
  

  HOW TO SET THE TIME

  1. Pull the crown out to the 2nd position when the second hand is at the 12’oclock position.
  2. Turn the crown to set the hour and the minute hands
  • when setting the minute hand, advance it to 4 or 5 minutes ahead of the desired time and then turn it back to the exact time.
  3. Push the crown back to the 1st position.

  
  
  * Do not change the battery in any solar watches, as this can cause damage to the movement. Solar watches should be charged by putting the watch in any light source. After 72 hours in an artificial light source or 8 hours in direct sunlight, the watch is fully charged. The watch will be automatically recharged as long as you wear it where there is light.
• AUTOMATIC
  

  WINDING THE MAINSPRING
  Automatic winding watch can also be hand winded by turning the crown clockwise in Normal position. Wind several times clockwise. It will start to move naturally.
  
  SETTING THE TIME

  1. Pull the crown out to the 2nd Click Position.
  2. Turn the crown to set hour and minute hands.
  3. After the time has been set, push the crown back to the Normal position.
     *24Hour hand moves linked with the center Hour and Minute hand.

  SETTING THE DATE

  1. Pull the crown out to the 1st Click Position.
  2. Turn the crown counter-clockwise to set the date.
     * If the date is set between the hours of around 9:00 PM and 1:00 AM, the date may not change on the following day.
  3. After the date has been set, push the crown back to the normal position.
• DUAL TIME
  

  ADJUSTING DUAL TIME HANDS POSITION

  • After setting or changing the battery, before setting the time, check if the dual time hour hand and dual time minute hand are at the “0” (12 o’clock) position.
    * If either the dual time hour hand or the dual time minute hand is not at the “0” position, reset it/them following the procedure shown below:

  1. Pull out the crown to second click
  2. Keep the buttons A & B pressed at the same time for more than 2 seconds, then release the buttons.
     * Dual time minute hand moves and returns to where it was
  3. Press button A or B to reset the dual time hands to “0” position.
     • Button A : dual time hour hand and dual time minute hand move counter-clockwise
     • Button B : dual time hour hand and dual time minute hand move clockwise
     • The dual time hour hand moves correspondingly with the dual time minute hand
     • The dual time hour hand and dual time minute hand move quickly if the respective buttons are kept pressed.
  4. Push the crown back in the normal position.

  LOCAL TIME SETTING

  1. Pull out the crown to second click when the second hand is at the 12 o’clock position.
  2. Turn the crown to set the hour and minute hands. (make sure 24 hour hand is set correctly).
  3. Push the crown back in the normal position in accordance with a time signal.

  • The 24 hour hand moves correspondingly with the hour hand.
  • The moment the date changes is midnight. When setting the hour hand, make sure that AM/PM is correctly set by using the 24 hour hand as an AM/PM indicator.

  DUAL TIME SETTING
  * When moving to a country or area in a different time zone, adjust the dual time hour hand to that countr/area.
  Quick set the dual time:

  1. Crown at normal position.
  2. Adjust the time by pressing the button A or B.
     • Button A : -1 hour / push
     • Button B : +1 hour / push

  Precise adjustmen of the dual time:

  1. Pull out the crown to second click when the second hand is at the 12 o’clock position.
  2. Adjust the time by pressing the button A or B.
     • Button A : -1 minute / push
     • Button B : +1 minute / push
  3. Push the crown back in the normal position in accordance with a time signal.

  DATE SETTINGS
  * Before setting the date, be sure to set the time.

  1. Pull out the crown to the first click.
  2. Turn the crown clockwise until the desired date appears.
  3. Push the crown back in the normal position.

  * Do not set the date during any time between 9:00 P.M. and 1:00 A.M. Otherwise, the date may not change properly. If it is necessary to set the date during that time period, first change the time to any time outside it, set the date and then reset the correct time.